Absolutely! Just send us a picture of your driver's license along with a picture of a valid Military ID. You can email it to sales.team@dirtydingo.com or just text us at 480-256-8434. If you are sending a picture of your active duty CAC card, all we need to see is your name and photo. The credit/debit card used must match the name on the Military ID.

   Photocopying U.S. government identification is a violation of Title 18, U.S. Code, Part I, Chapter 33, Section 701 and is punishable by fine and/or imprisonment.  It is acceptable to provide military or government ID to commercial establishments but they cannot copy or duplicate it in anyway.

   A valid Military ID is an identity document issued by the United States Department of Defense to identify a person as a member of the Armed Forces or a member's dependent, such as a child or spouse. The primary types of U.S. military ID cards being issued today are the CAC (for active duty members of the military), the DD Form 2, and Department of Defense Form 1173, for retirees and dependents. The DD Form 2 is commonly mistaken with the DD 1173 (as they are similar in appearance), however they are two separate forms. The DD Form 2 form number is appended with one of five codes to denote branch of service (A, AF, N, MC, or CG).

Measuring from the rear of the bell housing to the lower bolt on the small block Chevy 3 bolt vs the front bottom hole on the LS engine is 1 5/16"

 The small block and big block Chevy use a 3 bolt engine mount pattern, an LS series engine uses a 4 bolt pattern.

Belt numbers for our accessory brackets can be found at the bottom of the install instructions. If you are running one of our high mount AC then the belt number can be found at the bottom of the AC install page. The belt size will differ if you have a small case or large case alternator, if you are running smaller power steering pulleys and if you are running an underive balancer. If you are not sure what kind of alternator you have, we have example pictures of the differences below the belt numbers on every install page. If you are running one of our small diameter power steering pulleys, then you subtract two inches from the belt. Different brands of belts stretch differently, so you can't match the same length Gates to a Dayco belt, but you are able to cross reference the part numbers for an alternative.

We currently only make accessory brackets for LS GEN III/IV and LT GEN V engines, but we still make conversion mounts for SBC/BBC! LS GEN III/IV series engines and LT GEN V engines are faster, stronger, lighter and get better fuel economy than SBC/BBC's. If you are scared of Fuel Injection, then convert the LS Series engine to use a carburetor! We still make conversion mounts for SBC/BBC!

   Use the "Search by Model" feature. It is located in the big red box on the left for desktop viewers or it is the first drop down menu on mobile. If you are on mobile, then I recommend scrolling to the bottom of the page and clicking on "View Desktop Site" to see the website in its full glory. DO NOT reuse old rubber motor mounts or your engine will sag, not line up correctly, and will make the ride feel horrible. Get brand new motor mounts from a parts store or invest into polyurethane replacements from Energy Suspension. We stock a 3 bolt and 4 bolt polyurethane inserts from them. You have to drill out the rivets of your old GM mount to open it up and replace that old rubber piece. It helps if you zip tie the drilled out rivet hole before bolting the motor mount back to the chassis. 2WD FRAMES ARE DIFFERENT THAN 4WD FRAMES!

3 Bolt Style to replace the inserts of the following GM type mounts: 15731260 / 15529451 / 15529452 / 15592505 / 22145334 and aftermarket part number 2412.

4 Bolt Style to replace the inserts of the following GM type mounts: 14039437, 9762326, 467422, 10001132, 10001133, 9764714, 459021 and aftermarket part number 2292.

   No. It is not cost effective to make custom brackets for your application. Unless you have a 1948 Tucker or something from the Area 51 raid. Then we are VERY interested.

   We currently only make transmission crossmembers for 2WD 1963-1987 and 1988-1998 C10 C20 Truck's, Blazer's, and Suburban's.

Negative Ghost Rider.